How to change the password for wifi intercom. How to change wifi password on computer
Almost all modern laptops, tablets, phones support WI-FI and can work in wireless networks. Therefore, almost every apartment uses its own wireless network. Basically, home and office local networks that have access to the Internet from various devices are created using a router. At the same time, a gateway (router) is installed at the entrance to such a network. The router is configured via the web interface. It is very important when setting up the router to correctly configure the network security settings, and to know how to set a password on the router and on your WI-FI network. To enter the router settings menu, you need to know the password to enter the router. If you have not changed the password yet, then this is the default password and you can find it from the instructions or look at the bottom cover of the router. The table below shows the standard router passwords for the most common models.
How to see the password on the router
To find out the factory password of the router, you need to turn the router over and look at the bottom cover for the default password and login of the router.
How to password protect your router
To protect the router, the password is changed on the router. This setting is carried out after connecting the router to the computer and configuring the router. In this article, we will consider setting a password using the example of a D-link DIR-300 router (router), as the most common one. If you have a router from other manufacturers, such as Asus, Zyxel, TP-Link, Neatgear, then the password is set according to the same principle and it will not be difficult to figure out how to enter the password on the router.
All settings made can be easily changed or deleted if you have access to one of the computers local network. In addition, if a VPN server is configured on the router, then access to your local network can be obtained via the Internet. Having access to the router, you can easily access the data of all computers on your network. Therefore, it is recommended to change the factory settings and change the password used for authorization in administrative panel router. You need to know how to password-protect a router. Thus, you can protect your router from unauthorized access and reduce the risk of the router being hacked.
How to password-protect a d link router
To protect the router, you need to change the factory default password of the router to your own. In the example, we will use the D-link DIR-300 model. To get started, you need to type the address of the router in the Internet browser you are using. In our case, enter 192.168.0.1.
In the window with authorization, you need to enter the login (UserName) and password (Password) of the router in the appropriate fields. By default, the password for the d link router is admin, and the login is also admin. When you enter these values, you need to click the Log in button.
In the router management window, you need to select Maintenance from the top menu. And then from the submenu you need to select Admin Setup. In the window that opens, you need to find a field called New password and enter a new password value. Then duplicate the value in Confirm password. Click Save Settings to save your changes.
If you want, you can enter a new login value instead of the default admin. After this setting, your router will be protected from third-party connection and interference. It is better to come up with a password that is complex enough to be difficult to guess. To do this, enter a value consisting of at least eight characters and use numbers, uppercase and lowercase letters of any alphabet.
How to change the password on the router
If you do not know how to change the password on the router, then you need to follow all the steps above to set the password. In this case, you enter the router settings no longer under the factory password, but under the one that you set earlier. You just need to write a new password value instead of the old one in the corresponding window of the Admin Setup menu and save the settings.
Reset your router password
It often happens that someone forgot the password from the router or lost it. Perhaps, in your case, you got the router from another owner and you do not know how to find out the password. In addition, some providers, when they ship their router, set their own password on it to protect the router from outside interference. Then, without knowing the password, you will not be able to enter the router settings in any way. In this case, it remains only to reset the settings to the default values. You need to know how to reset the password on the router.
If you need to reset the router settings to factory defaults, then this is solved by simply pressing the Reset button on the router. All routers are equipped with such a button. The button is a small hole on back cover router. The button itself is located in this hole. Above the hole, there is usually an inscription Reset. Such a non-standard button design is made on purpose so that you cannot accidentally reset the settings. Although accidental pressing of the button is protected, it is advisable to seal the button hole with tape, just in case.
First you need to supply power to the router, then press Reset with a convenient tool (a paperclip, a pen rod) and hold the button down for about 7 seconds. But it's better to wait ten seconds. After pressing the router will go to reboot and you can not turn it off for several minutes. After that, you can use the default password value to enter the router menu. You can find out what password the router has by default from the instructions for your router model, or from the factory password table, which is given in this article.
Perhaps you need to reset the values to the factory settings, not because you do not know the password, and you have access to the router's menu. Then you can reset the settings from the router menu. To do this, open the Tools item (settings) in the router menu and navigate there a button called Settings Reset. After pressing the button, your router will reboot. You need to wait about two or three minutes and the router settings will be reset.
You should also be aware that there are cases of spontaneous resets that occur during strong network drops. In this case, the Internet may turn off for a while and the router will reboot. In this case, it may happen that the router does not accept the password if the settings are reset and you enter your set password value. Then you need to enter the factory password value. To combat this problem, it is recommended to use uninterruptible sources nutrition.
How to password protect a wifi router
The use of Wi-Fi wireless connection is very convenient and thanks to such a connection, you get access to the Internet from anywhere in the apartment. However, do not forget that using a wireless connection is more dangerous than a wired one. After all, the signal of your home W-Fi network can be picked up by neighbors or someone on the next floor. In this case, an unauthorized person can enter your network and gain access to information on your computer.
Many users do not initially think about the safety of data on their computer and whether it is easy to access the computer from the outside. Therefore, not everyone sets up restrictions on access to the local network. The consequences of such neglect are noticed only when there are clear signs of outside interference in the system. To restrict unauthorized access to the network, you need to put a password on the Wi-Fi network. Setting such a password is done through special settings in the router menu.
There are several ways to restrict access to a wireless network. The easiest way to set up is password access. To do this, you need to know how to change the password on the router. All users must enter an access password to access the network.
To make the necessary settings, you need to connect your computer to the router and go to the router's web interface. We type in the address bar of the browser the address of the router as in the picture below.
If the address is entered correctly, the authorization page will open. You need to enter your password and username in the appropriate fields. If you have already changed them, then enter your own values, and if not, then the factory ones that come by default. The default password for the d link router is admin.
When you get to the router settings page, find the Setup item in the main top menu. From the left menu, open Wireless Setup to configure your wireless network.
Before setting up a password on the router, you need to select the manual setting option or using the setup assistant. To select the appropriate option, you need to click the appropriate button.
How to password-protect a Wi-Fi router using the setup assistant
If you decide to set a password using the assistant, then after clicking on the appropriate button you will be taken to the message page. The message says that the setup is done in two steps. First, a general setup is carried out, and then a password is set. To continue the configuration, click Next. If you decide to cancel the setting, then click Cancel.
On the next setup page, you will be prompted to select a password assignment option. You can assign a password manually or automatically. Choose the option as in the picture below if you want to create your own password.
If you doubt that you can come up with a good password yourself, you can choose the automatic assignment option. However, in this case, it will be more difficult to remember. The WEP encryption option is best left enabled. This will use a more advanced encryption security method.
When choosing automatic installation password in the settings window you will see the value set password and some parameters of your network. You just have to write down the password and click Save. If you want to go back one step, press Prev.
If you set the password yourself, then on the settings page that opens, you need to enter the invented Wi-Fi network password in the appropriate Network Key field. Password length should not be less than 8 characters and it is recommended to enter letters and numbers for password strength.
When you enter your password, remember or write it down and click Next. In the next window, click Save and your password will be set.
Setting a password on the router manually
In order to set the password manually, you need to select Wireless Setup in the menu of the router, and click Manual Wireless Connection Setup there. A page with settings will open in front of you, where you need to find the Security Mode and select a position from the list, as in the figure below. In the same window, enter your Wi-Fi password opposite the Network Key.
To complete the installation and save the settings, click Save Settings. When connecting computers, netbooks, and other devices to your wireless network, you will need to enter this password to enter the network.
How to find out the password of a Wi-Fi router
Sometimes it happens that someone forgot the password from the wifi router and cannot enter the network. Let's say you forgot to write down the network password. It is possible that if the devices you use are connected to you yet and you do not need to enter a password. But when connecting a new device, you will definitely need the password value of your network and you need to know how to recover the password on the router. This problem is not at all difficult to deal with, and it only takes a few simple steps. To restore forgotten password You need at least one computer connected to your network. Then you can go to the network settings from it. You need to turn on your computer and click on the network connection icon, which can be found in the lower right corner. Select as in the figure below the network management item and click on it.
In the Network Control Center window that appears, you need to find the item on the right that is responsible for setting up wireless networks, as in the figure below, and click on it.
In the new settings window, you need to right-click (right-click) on the connection, and select the Properties item in the context menu that opens.
After that, you need to open the tab called Security, and then look in the corresponding field for the value of your password (security key). Perhaps in the password field you will see only asterisks (hidden characters), then you will need to enable the option below by checking the box next to the item display hidden characters. After that, you will definitely see the value of the network password and you can write it down so as not to forget.
Many people are interested in the question of how to change the password on a D-Link router. I have to introduce the owners of the routers of this company. And since D-Link is very popular, I think the article will be useful and relevant. I have to enter a password change on a Wi-Fi network. Simply, the router has another password that is used when entering the settings. Also, the question of changing the password on D-Link is very popular if the Wi-Fi password has already been successfully forgotten. Try to deal with this problem.
Why change the password for a wireless network? Yes, there are different cases. For example, someone hacked your Wi-Fi, you noticed that some strange devices are connected to your router, or maybe you just gave your Wi-Fi password to a neighbor, and then changed your mind :) We change the password, and that's it, no one will connect to your network anymore. Always try to install a complex key that will be difficult to pick up. If someone connects to your router, then he will not only be able to use your Internet (which is not very scary), but will also be able to access your local network. And this, perhaps, is already your files and personal information.
Well, try to remember the passwords that you set. Or write them down.
Change password on D-Link
As usual, we need to go to the router settings. This is how it is done: connect to the router (via cable or Wi-Fi), in the browser we type the address 192.168.0.1 , specify the login and password. By default, D-Links have this admin And admin. Or, . The standard data for entering the settings is indicated at the bottom of the router.
In the settings, go to the tab WiFi/Security Settings and in the field
If you do not configure anything else, then save the settings. This is done by clicking on the link. System and choose Reload. Like this:
Restart your router (power off and on). Now, the new password you set will be used to connect to your Wi-Fi network. If after this procedure your devices refuse to connect to Wi-Fi, then you just need to delete your network on the device and connect to it again. Below, I will write about it in more detail.
How to change the password on Wi-Fi if you forgot the password?
In this case, everything is done in exactly the same way as I described above. Only, in the settings of the router you need to go through the network cable (so you don't need to enter a password), or from a device that is still connected to the wireless network.
In the settings, on the same tab WiFi/Security Settings you can see the old password (which is specified in the PSK Encryption Key field), or set a new key.
And if you do not have the opportunity to connect via a network cable, and there is not a single device connected via Wi-Fi, then most likely you will have to reset the router settings and configure everything again. After the reset, the network will either be unsecured, or a standard key will be used to connect to it, which is listed below the devices a (it's signed as a PIN).
What should I do if the devices do not connect to the network after changing the key?
The most common problem that occurs after a key change is when devices that were previously connected to the Wi-Fi network with the old password refuse to connect to it. This is due to the fact that the old key is stored in these devices, which does not match after the change. On computers, this is most likely the error "The network settings stored on this computer do not match the requirements of this network."
What you need to do, you just need to delete your Wi-Fi network on the device, and reconnect. On laptops with Windows 7, this is done in the control panel, in the section Control Panel\Network and Internet\Manage Wireless Networks. There we right-click on the network we need and select Delete network (then, we connect to it again with a new password).
On Windows 8, simply click on the name of the wireless network, and select " Forget this network". And on tablets, mobile phones, most likely you also need to click on the network (maybe press and hold) and select item Delete. It's different on every device.
If the router was just purchased and no one has configured it, you can connect to the newly created network without entering any identification data. That is, any owner of a device with a Wi-Fi module can use all the delights of the Internet without the permission of the owner of the equipment. To prevent this from happening, you need to change the password on the Wi-Fi router immediately after creating the network.
Perhaps the appearance of an extra user will not affect the speed - most providers are able to provide it with a decent level with unlimited traffic. But unfortunately, not everything is so simple. There are a number of negative circumstances, the possibility of which must be remembered, leaving the network without proper protection.
Each connected device requires the modem to allocate an IP address and hardware resources to ensure communication. All this creates an additional load on the distributing equipment, which, in turn, will negatively affect the speed and stability of the connection as a whole. In addition, the lack of password protection lowers the overall level of security and somewhat simplifies access to personal information.
The above is enough to think about changing the authorization settings, especially if there are none, for example, when starting a new router. Next, consider how to quickly change or install wifi password on routers from different manufacturers (not to be confused with the admin panel login settings). Some will be affected important points regarding security settings.
Password Rules
Not every new password is able to provide the proper level of security. Many users, especially beginners, prefer not to fool around and enter a set of simple numbers, for example, all units or 12345678. More resourceful ones use their name or date of birth. The meaning is clear: to think briefly and easily remember.
Video on compiling the correct password:
Hacking a network with such protection will take no more than 5 minutes even for a schoolboy who is not too lazy to read a couple of articles on the Internet. There are many programs that come with large dictionaries of frequently used security keys. It is enough to have a desire, a regular laptop or smartphone, to provide free access to the network of careless neighbors.
What should be the new password:
- You need to use 8 or more characters (the standard will not allow less);
- Must consist of Latin letters of different case (large and small), numbers, signs (@$# and others);
- The sequence of characters must be random and varied. That is, you do not need to enter 6 identical letters, but at the end several characters and numbers. A good password should inspire fear at the thought of having to remember it.
- As mentioned above, no prime numbers, names and dates of birth.
Some users find it difficult to come up with a replacement password on their own. Then you can resort to the help of special online generators that will make up a code of any length and complexity. In addition, the network has services for the selection and storage of protective data.
Video on working with the utility for creating and storing passwords:
Once a suitable password has been thought up or generated, it must be saved. You should not rely on your own memory, it is better to write it down on paper, for example, in a notebook. In parallel with the paper version, you can create a text file on your computer.
Suppose a password is generated or invented, recorded and stored on several media. This is of little use as long as it is not used in the security settings of the Wi-Fi network. Next, consider the process of changing the password on the router.
Changing the password
To change the security settings of the access point, you need to get into its management interface. To do this, you need to use the address bar of the browser or the utility supplied on the disk with some routers. The first way is simpler and more universal.
First, find out the IP address of the router. In most cases this is . The exact value is indicated on the label on the bottom of the device.
There you can also find out the data for user authorization, set by default. As can be seen from the figure, the login and password are admin. This combination is relevant for most models. If suddenly the sticker is lost or erased, the necessary information is in the instructions, if there is no instruction, we look on the Internet.
Here you need to activate the radio button indicated by the red arrow, and then adjust the margins below.
- Version. We leave "Automatic" for correct work with a large number of devices.
- Encryption. We choose AES (the most reliable and proven standard).
- PSK password. In this field, enter the invented or generated network security key.
After specifying all the necessary parameters, we confirm the changes by pressing the "Save" button and reboot the router. The offer to restart will appear on the same page. In the absence of it, a reboot is optional, but it should be done so that all connected Wi-Fi users are authorized. This can be done through the system tools.
After all the above manipulations, the first access to the wireless network will be possible only after entering the password. If over time you need to reinstall the security data, you will have to follow the same sequence of steps as for installing a new authorization key.
Difficulties that may arise during security setup
The most common problems are the absence or loss of the IP address of the admin panel or authentication data in it. It is solved simply: the router firmware is brought to the factory state using a special button.
On the TP-Link model, it must be pressed and held for 10 seconds. The settings will be reset to the factory settings and it will be possible to log in using the standard address using the admin / admin pair for authorization.
In case of loss or change of the IP address (for example, it was changed if there are several identical routers on the network), you can find it out by running the Windows console on a laptop or PC. To do this, you need to type the combination "Windows + R", the "Run" window will open, in which we enter "cmd". The console will launch. In it we write "ipconfig" and press "Enter".
Opposite the inscription "Main gateway" will be the address of the router to which the device is connected.
Changing the password on popular routers
Using the above sequence of actions, you can change the password on any Wi-Fi router. Differences can be in the access point management interface, its address and authorization data. Next, you need to find the wireless security tab or a similar menu item. Let's take a closer look at how the password is changed for popular models.
D-Link
Address: 192.168.0.1. Login/password pair: admin. On the main page, select "Advanced Settings" from the bottom.
On the next one, select "Security Settings" (circled).
Many wireless Internet users are wondering how to set their own password on a wifi router. Select the router model you need in the content and go to the settings.
Several factors contribute to this problem:
- The master installer did not report the key;
- No security password;
- Hacking a secret combination.
All this is fraught with serious consequences. On the router, protection should always be present, since it provides:
- Security of your personal computer and gadgets connected to the network;
- Improves router performance;
- Strangers do not use your traffic without permission;
- No one will get personal information stored on computer equipment.
Changing the key combination is a fairly easy process, which includes five basic steps:
- open home page device on your computer
- In the settings, find the Wireless / WLAN tab;
- In this tab, find the lines SSID (name) and PSK (key);
- You need to change them to your data;
- Save.
To make it easier to change your password, we suggest step by step instructions to the most popular router models.
In order for data change to bring maximum benefit, you must:
- Come up with a key combination of at least eight characters;
- Use Latin;
- Use numbers, capital and small letters;
- First, write down the secret code on paper, and then enter it into the system.
Change the code at least once a month and be sure about your security wifi networks.
D-Link
The devices of this company are considered one of the most popular. On all models, the access password changes in the same way. For this you need:
1. Launch any browser.
2. In the search, enter "192.168.0.1" or "192.168.1.1" and click on "Enter".
3. In the window that appears, enter your login and password. By default, this word is "admin".
4. After identification is completed, access to advanced device settings will open.
6. Now you see a window where you can change the key to your wifi. Near "authentication" select "WP2A-PSK" - the most secure encryption method. In the "PSK" line, enter the secret combination, then in order to change the data, click "Change" and "Save".
7. After that, restart the router and then connect to the wifi network through a new password.
Changing the password for other D-Link firmware is almost identical, the same tabs, the same names, only the view changes, you can see more details.
ASUS
Asus produces a large range of routers that are very simple and easy to use. To change the cipher, do the following:
1. Launch your browser.
2. In the search field, enter the address of the router "192.168.1.1", click "Enter".
3. In the authorization field, enter "Admin" as login and password. If the wizard has already set a limit on your wifi network, then enter this data.
4. Go to " Wireless network».
5. Now you need to fill in the "Authentication Method" lines. Here you need to set WPA2-Personal, and in the line "WPA Encryption" select "AES". Now enter the new secret combination in the WPA Preshared Key.
To change the access password for a newer firmware from Asus, you must:
- After the standard entrance to the router settings panel, on the left side menu, select "Wireless Network".
- In this tab, you fill in the SSID - enter any word here in Latin letters, select WPA2-Personal in the "Authentication Methods", and in the "WPA Preshared Key" enter a new key and click on "Accept".
Be sure to restart the router and work with a new wifi password.
TP Link
The devices of this company are distinguished by high reliability, long-term operation and simplicity. Every user can change the password on it very easily and quickly. For this you need:
1. Launch any convenient browser.
2. Enter 192.168.0.1 or 192.168.1.1 into the browser address bar and press ENTER.
3. In the authorization field that appears, enter the standard word "admin". If the wizard did not change the standard password when installing the router, then enter its data.
4. After entering the login and password correctly, the main settings window of the device should appear.
5. Here find the "Wireless" tab.
6. Then go to "Wireless Security".
7. Enter a new secret combination.
8. Click on "Save".
9. A red inscription with an active link "click here" will appear.
10. By clicking on it, you will see the Reboot button. Clicking here will reset the modem.
11. After switching on, enter new access data on gadgets and use a secure wifi network.
ZyXEL
A very popular router in our country. All users note it as a high-quality modem, nice appearance and easy operation. Today there are two types of devices from this manufacturer, and changing the key for them has slight differences.
1. Open a browser.
2. In the search field, enter 192.168.1.1 and click Enter.
3. For authorization, enter "admin" in the "login" field and "1234" in the "password" field, then "Login".
4. To change the password, go to "Wi-Fi network" and click on "Connection". In the appeared field "SSID" enter the name of your network and click "Accept".
5. In the same window, select "Security". Set "Authentication" to "WPA-PSK/WPA2-PSK".
6. The correct wifi password format must be "ASCII". In this field, carefully enter a new combination.
7. Click "Accept" to save.
For a different firmware version, the input remains the same, but the further steps are slightly different:
1. To go to the router settings, you need to click on the wifi icon on the bottom panel.
2. Open the "Access Point" section.
3. We type "Network name (SSID)".
4. In "Network Protection" select WPA2-PSK.
5. In the Network Key, enter a new code.
6. Click Apply.
7. Now reboot your device.
ZTE
This manual is suitable for all models of this manufacturer.
1. Check the connections of the router to the computer.
2. Open a browser.
3. Enter 192.168.1.1 in the address bar and press ENTER.
4. The system will require authorization. To do this, enter the word "admin" in the line Usename and Password.
5. After entering, click Login.
6. Go to the "WLAN" section, where you need to select "Multi-SSID Settings".
7. Find the line "SSID Name" and enter any word there in Latin letters.
8. Save with the "Submit" button.
9. In this window, find "Security".
10. Next to the "Authentication Typr" field, select the WPA2-Personal encryption type.
11. In the line "WPA Passphrase" type a new password.
12. Click "Submit" to save the changes.
Huawei
On this router, changing the key is as easy as on the rest:
1. Launch the browser.
2. Enter 192.168.100.1 in the address bar.
3. The authorization window will require you to enter data. Most often these are such combinations:
- telecomadmin \ admintelecom (the most common).
- root\admin.
- Login - telecomadmin with different keys - NWTF5x%RaK8mVbD, nE7jA%5m, NWTF5x%.
5. In the line "SSID Name" enter your own invented name for Wi-Fi.
6. In the "Authentication Mode" line, set WPA2Pre-SharedKey and immediately enter a new password.
7. Click "Apply".
Sagemcom
Change the key on this device is a standard procedure:
1. In the address bar of an open browser, enter 192.168.1.1.
2. For authentication, enter "admin" as Login and Password, click "Login".
3. A new window will appear. In these settings, find "WLAN Settings".
4. Select the "Basic" item, in it, next to "SSID", enter a new name for WiFi, if necessary. Save.
5. Immediately go to "Security".
6. In the "Select SSID" should be the name that you entered a few seconds ago.
7. In "Authentication" choose "Mixed WPA2/WPA-PSK".
8. In the "WPA / WPAI password" enter new data and save.
Reboot the device, update the secret combination on the laptop and gadgets, and use a secure wifi network.
Altel 4G
Changing the key on this router is just as easy as on other devices.
1. Enter 192.168.0.1 or http://m.home in your browser's address bar.
2. The system will ask for a password. There will be a standard word here: password.
3. Click on "Login".
4. Go to "Settings".
5. Here choose " WiFi settings».
6. In the line "Wi-Fi network name (SSID)" write any word in Latin letters.
7. Save the actions with the "Apply" button.
8. In this window, select Security Settings. Set the mode shown in the image below. In the empty line "Password" we specify a new security key.
9. Click "Apply", reboot the device and then you can continue working.
https://youtu.be/SA4iE2EloUs
Found a typo? Select the text and press Ctrl + Enter
The 21st century is the era of digital technologies, which are changing and improving every year. The Internet penetrates our lives at an incredible speed, which is what scammers use. In addition, it is possible that your neighbors could also connect to your Wi-Fi and use it for their own needs. In order for your computer to be always protected, it is necessary to change the password from time to time. WiFi router. How to do it?
Important! How to make the most secure? Do not write too simple a password, the recommended length is eight or more characters; so that attackers cannot pick up the coveted combination, use a combination of numbers, letters (uppercase and lowercase), for example: rpUk1B5y9; name/date of birth/any other personal information should not be used as a password; use a special generator that can be easily found on the Internet if you have difficulty coming up with a password.
Step 1. Connect the router to the computer
- Connect the cable from the router to your computer or laptop, as shown in the photo below, or simply go to any browser via Wi-Fi, but the first option is more reliable.
- Take a router and find the IP address (192.168.1.1/192.168.0.1 - in most cases). The IP address, username and password are easy to find by looking at the back of the device, as well as in the instructions for the device.
- If the password has already been changed by you, but you cannot remember it, you need to reset the settings to return to the basic ones. To do this, find "Reset" on the device and hold for some time (10 seconds).
- If you have trouble finding the IP address, click on the Start menu. Type "cmd" in the search bar and press Enter.
- IN command line enter the word "ipconfig", then the line "default gateway" will appear, where the IP address will appear.
- Login to the browser ( Google Chrome, Yandex, Opera or any other browser installed on your computer), enter these numbers in the address bar and press Enter.
Step 2. Enter the "Settings" of the router
A window will appear in which you need to enter (if you used the first method to search for an IP address, then you already know this data). If you have not changed your password before, then you need to type "admin" in both fields, i.e. standard options. If the password has already been changed by you, then enter your choice (if you do not remember it, then return to step 1 and reset the settings).
Step 3: Change your password
Remember that for the complete security of your computer, the password should be changed from time to time ( better times in 1-2 months), and do not forget to write down the new password.
Attention! If after changing the password there are connection problems, a window appears with the inscription "error", then you need to delete the connection to your Wi-Fi, reconnect and enter a new password.
You can also watch a video to learn more about the password change process.
Video - How to change your Wi-Fi password
Loading...
